FBS Studs for the Full Branch Shoe
Item No.: GS2
from 1,77 EUR
incl. 19 % VAT
-
- delivery time 3-5 Werktage (*)
Are you already benefitting from our commercial conditions? Please contact us!
FBS Studs – Optimized grip for the Full Branch Shoe
The Full Branch Shoe not only follows the design of a traditional horseshoe with its metal core and classic branches, but also uses the same proven approach for stud installation. Studs can be added manually whenever needed, giving you the flexibility to choose both the number and the exact position of the stud holes on site, depending on the horse, the footing, and the intended use. For retrofitting studs, we have developed a specially designed stud for this purpose: the FBS Stud.
Choosing the Right Ground Conditions
FBS Studs are designed for permanent use with the Full Branch Shoe. When deciding whether to use studs, always consider the prevailing ground conditions to keep stress on both the horse and the horseshoes as low as possible.
Selecting the right stud requires looking at several factors. In many cases, a compromise is necessary, as a permanently fitted stud must perform well both while the horse is working and during its rest periods. On very hard ground in particular, studs that are too high and cannot achieve sufficient grip or penetrate the surface may increase stress on both the horseshoes and the horse's musculoskeletal system over time.
Step-by-Step Guide to Installing Studs on the Full Branch Shoe
Fit the Full Branch Shoe to the shape of the hoof and mark the drilling positions.
The stud holes should be positioned as close as possible to the center of the metal core.
Placing them too close to the edge of the shoe may reduce the strength of the horseshoe and the secure
retention of
the stud.
Drill completely through the Full Branch Shoe using an 8.5 mm HSS twist drill bit . At low temperatures, it is recommended to warm the tip of the drill bit slightly. This makes it easier to start drilling through the plastic outer layer and helps prevent the bit from slipping.
Cut an M10 thread into the prepared hole using an M10 thread tap. We recommend tapping the thread from the ground side of the horseshoe, as this prevents burrs from forming on that side and makes it easier to install the stud later.
Screw the stud into the threaded hole of the Full Branch Shoe. The stud is designed so that the threaded end extends slightly beyond the plastic edge on the hoof side of the horseshoe. This protrusion is required to provide enough material for riveting in the next step.
Position the stud so that the carbide pin is aligned over a small hole or recess in the anvil to protect its surface. Then rivet the stud from the hoof side with a firm hammer blow. This increases the stud's holding strength in the horseshoe and reduces the risk of it loosening and unscrewing during use.
Make sure that the end of the thread cannot put pressure on the hoof sole . We recommend that, after riveting, the end of the thread finishes at least 1 mm below the surface of the plastic outer layer.
Installing Studs on the Full Branch Shoe – Video
Even the best step-by-step guide cannot always match seeing the process in action. Some techniques are simply easier to understand once you've watched them being performed.
Take a look at our Full Branch Shoe video. It not only introduces the new horseshoe with regular-length branches in detail, but also walks you through every step of the stud installation process—from fitting the horseshoe to the hoof to installing the FBS Studs.
Shoeing a Horse with the Full Branch Shoe
Product Specifications
| General Information and Shipping Details | |
|---|---|
| Product | FBS Studs |
| Brand | Duplo |
| Product Range | Innovations test range at reduced introductory prices |
| Made in | Germany |
| Item Number | FBS Hexagonal Stud M10, 7 mm: 001350 FBS Conical Stud M10, 8 mm: 001351 | 12 mm: 001352 M10 Thread Tap: 042010 HSS Twist Drill Bit – 8.5 mm: 042011 |
| Pack Size | Sold individually |
| Returns and Exchanges |
Returns and exchanges are possible within 3 months under certain conditions for customers within
the European Union (EU). For returns from outside the EU, please contact our customer service team. Full details can be found under FAQ → Service & Terms. |
| Features, Functions and Required Tools | |
|---|---|
| Function | Screw-in studs, additional grip, winter horseshoes, improved slip resistance |
| Required Tools for Stud Installation |
|
| Compatible Composite Horseshoes | FBS Studs are designed exclusively for use with the Full Branch Shoe. |
| FBS Stud Variants |
|
| Stud Features | Because FBS Studs are additionally riveted after installation, they are not fully hardened . The galvanized finish and the carbide pin are identical to those used on our other studs. |
| Application Notes |
The use of FBS Studs is at your own discretion and should always be adapted to the ground
conditions, riding discipline, and safety within the herd. FBS Studs are not designed for frequent installation and removal. Instead, they remain permanently fitted in the Full Branch Shoe. |
| Safety Information for the Use of Permanent Studs | |
|---|---|
| The following information is based on the current legal framework and available knowledge in Germany. It does not constitute legal advice and makes no claim to be complete or up to date. Legal regulations, official requirements, insurance terms and conditions, and sporting rules may change or vary from country to country. Before using permanent studs, the user is responsible for checking the regulations that apply to the intended area of use. | |
| Online Safety Information | Please read the additional information on the use of studs in our safety guidelines. These are available online under FAQ → Safety Information. |
| Safety Information (PDF Download) | Download PDF |
| Risk of Injury |
Using FBS Studs increases the risk of injury. We accept no liability for any damage or injury resulting from their use. Using studs on hard ground may negatively affect both the horse's musculoskeletal system and the stability of the horseshoes. Although FBS Studs provide additional grip, riding on icy or snowy surfaces always involves risk. No matter how well a horseshoe is equipped, a horse can still slip. Always ride at an appropriate speed and use extra caution. |
| Group Housing / Herd | Permanent studs may increase the risk of injury to other horses during dominance disputes, kicking, or close contact. Before using this type of horseshoes in a herd, it should be assessed whether it is suitable for the specific housing conditions. |
| Horse Owner’s Liability Insurance | The use of permanent studs may raise liability and insurance-related questions in the event of damage or injury. Before use, check with your horse owner’s liability insurance provider whether coverage applies and, if so, to what extent. |
| BMEL Guidelines / Animal Welfare | The BMEL guidelines on horse keeping and applicable animal welfare regulations focus on avoiding preventable risks of injury. In individual cases, the relevant authorities may impose requirements relating to housing conditions and horseshoes. |
| Competitions and Events | Requirements for the use of studs may vary depending on the organizer, competition rules, or sports association. Check the applicable regulations before taking part. |
| Horse Transport | During transport, care must be taken to ensure that horseshoes fitted with permanent studs do not create an increased risk of injury to the horse itself or to other horses. Suitable protective measures or adapted transport arrangements may be required. |
| International Regulations | Regulations, legal requirements, animal welfare provisions, and sporting rules may vary from country to country and may change at any time. Before use, check the regulations that apply at the place of use. |
| User Responsibility | Before every use, the user is responsible for assessing whether permanent studs are suitable for the intended purpose and the specific conditions of use. This includes, in particular, compliance with all applicable legal, animal welfare, insurance, and sporting requirements. Legal regulations, insurance terms and conditions, and association rules may change or vary from country to country. The user is responsible for checking the applicable requirements before use. |
| Assessment of Benefits and Risks | Permanent studs should only be used when the expected safety benefit of improved traction justifies the increased risk of injury to people and animals under the specific conditions of use. Stud height, stud shape, duration of use, and area of use must be carefully selected to suit the relevant conditions. |
| Intended Use | This product is intended exclusively for proper, professional use in accordance with its intended purpose. Any unintended, improper, or unprofessional use, as well as use under unsuitable conditions, may significantly increase the risk of injury to people and animals. The manufacturer has no control over the specific conditions of use, the selection of the stud height, the housing system, or the actual use of the product. The user is responsible for ensuring proper use in accordance with the intended purpose. |
