Glue-U SHUBOND Acrylic Glue for Maximum Bonding

General Application and Safety Instructions

Please follow the safety instructions provided by Glue-U and wear the required protective equipment. In the section FAQ → Safety, we’ve compiled all the important information about the necessary safety precautions when working with various hoof care tools.

Videos on Using SHUBOND

From SHUBOND itself to properly using the cartridges and applying it to the hoof — Glue-U provides a variety of videos about its products online. We encourage you to visit the Glue-U YouTube channel for detailed guidance.

Frequently Asked Questions About Working with SHUBOND

Glue-U answers the most common questions about SHUBOND on its website. We'd like to make those answers available to you here as well.

FAQ: Which Horseshoes Can Be Glued with SHUBOND?

Almost all horseshoes made of aluminum and steel, as well as many synthetic shoes.

FAQ: How Hot Does SHUBOND Get During Curing, and How Can You Protect the Hoof Wall ?

A thick layer of SHUBOND can heat up to 75°C / 167°F during curing. For larger repairs where a thicker layer is needed, it can be helpful to apply a thin layer first and let it cure before adding another layer. This initial thin layer can help protect the hoof from the higher temperatures of the curing process when the thicker layer is applied.

FAQ: How Should the Hoof Be Prepared?

Before working with SHUBOND, the hoof must be clean and dry. Be sure to remove any loose material and roughen the hoof wall, for example, with a wire brush. When rasping, use only the coarse side of the hoof rasp to ensure better bonding.

FAQ: How Long Does SHUBOND Take to Set?

As mentioned above, there are two variants. On average, SHUBOND takes about 3.5 minutes to set at room temperature. The curing time can be shortened by warming the adhesive to body temperature. Especially in winter, using a heater can be helpful to properly warm the cartridge.

FAQ: Kann man durch SHUBOND nageln?

FAQ: Can You Nail Through SHUBOND?

It is possible to nail through the cured layer, even afterward. However, Glue-U recommends nailing within one hour after applying SHUBOND.

Warnings and Safety Precautions

For more details and first aid instructions, please refer to the safety data sheets provided by the manufacturer, as well as the information on the product packaging.

Component A

UFI Number

TA02-FHXA-D99V-AF6Q

Hazard Statements

• H410 – Very toxic to aquatic life with long-lasting effects.
• H319 – Causes serious eye irritation.
• H315 – Causes skin irritation.
• H317 – May cause an allergic skin reaction.

Safety Instructions

• P261: Avoid breathing vapors.
• P264: Wash thoroughly after handling.
• P280: Wear protective gloves / protective clothing / respiratory protection / eye protection / protective footwear.
• P302+P352: IF ON SKIN: Wash with plenty of water.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
• P501: Dispose of contents/container in accordance with regulations for hazardous waste or packaging waste.

Additional Information

EUH205: Contains epoxy-based compounds. May cause allergic reactions.

Component B

UFI Number

QNKD-7UW6-6W0R-8SE1

Hazard Statements

• H302 – Harmful if swallowed.
• H224 – Extremely flammable liquid and vapor.
• H314 – Causes severe skin burns and eye damage.
• H317 – May cause an allergic skin reaction.
• H335 – May cause respiratory irritation.

Safety Instructions

• P210: Keep away from heat, hot surfaces, sparks, open flames, and other sources of ignition. No smoking.
• P280: Wear protective gloves / face protection / protective clothing / respiratory protection / protective footwear.
• P301+P330+P331: IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
• P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
• P370+P378: In case of fire: Use foam extinguisher (AB), dry chemical powder (ABC), or carbon dioxide fire extinguisher (BC) to extinguish.